Note: Setup for chemical atmospheric control during in situ grazing incidence X-ray scattering of printed thin films.

In order to tailor the assembling of polymers and organic molecules, a deeper understanding of the kinetics involved in thin film production is necessary. While post-production characterization only provides insight on the final film structure, more sophisticated experimental setups are needed to probe the structure formation processes in situ during deposition. The drying kinetics of a deposited organic thin film strongly influences the assembling process on the nanometer scale. This work presents an experimental setup that enables fine control of the atmosphere composition surrounding the sample during slot die coating, while simultaneously probing the film formation kinetics using in situ grazing incidence X-ray scattering and spectroscopy.

Codependence between Crystalline and Photovoltage Evolutions in P3HT:PCBM Solar Cells Probed with in-Operando GIWAXS.

We address the correlation between the crystalline state of photoactive materials in a model organic solar cell based on poly(3-hexylthiophene-2,5-diyl):phenyl-C60-butyric acid methyl ester (P3HT:PCBM) and the photovoltage in an in-operando investigation. I-V curves are simultaneously measured together with grazing incidence wide-angle X-ray scattering probing the crystalline state of the device active layer as a function of the operation time. The results show a high degree of correlation between open-circuit voltage VOC and the crystalline state of P3HT.

Laser-Induced Periodic Surface Structures on P3HT and on Its Photovoltaic Blend with PC71BM.

We describe the conditions for optimal formation of laser-induced periodic surface structures (LIPSS) over poly(3-hexylthiophene) (P3HT) spin-coated films. Optimal LIPSS on P3HT are observed within a particular range of thicknesses and laser fluences. These conditions can be translated to the photovoltaic blend formed by the 1:1 mixture of P3HT and [6,6]-phenyl C71-butyric acid methyl ester (PC71BM) when deposited on an indium tin oxide (ITO) electrode coated with (poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS). Solar cells formed by using either a bilayer of P3HT structured by LIPSS covered by PC71BM or a bulk heterojunction with a P3HT:PC71BM blend structured by LIPSS exhibit generation of electrical photocurrent under light illumination. These results suggest that LIPSS could be a compatible technology with organic photovoltaic devices.

Arrangement of Maghemite Nanoparticles via Wet Chemical Self-Assembly in PS-b-PNIPAM Diblock Copolymer Films.

The structure and magnetic behavior of hybrid films composed of maghemite (γ-Fe2O3) nanoparticles (NPs) and an asymmetric diblock copolymer (DBC) polystyrene61-block-polyN-isopropylacrylamide115 are investigated. The NPs are coated with PS chains, which allow for a selective incorporation inside the PS domains at different NP concentrations. Upon incorporation of low amounts of NPs into the DBC thin films, the initial parallel (to film surface) cylinder morphology changes to a well ordered, perpendicularly oriented one. The characteristic domain distance of the DBC is increased due to the swelling of the PS domains with NPs. At higher NP concentrations, the excess NPs which can no longer be embedded in the PS domains, are accumulated at the film surface, and NP aggregates form. Irrespective of NP concentration, a superparamagnetic behavior of the metal oxide-DBC hybrid films is found. Such superparamagnetic properties make the established hybrid films interesting for high density magnetic storage media and thermoresponsive magnetic sensors.

Development of the morphology during functional stack build-up of P3HT:PCBM bulk heterojunction solar cells with inverted geometry.

Highly efficient poly(3-hexylthiophene-2,5-diyl) (P3HT):phenyl-C61-butyric acid methyl ester (PCBM) bulk heterojunction solar cells are achieved by using an inverted geometry. The development of the morphology is investigated as a function of the multilayer stack assembling during the inverted solar cell preparation. Atomic force microscopy is used to reveal the surface morphology of each stack, and the inner structure is probed with grazing incidence small-angle X-ray scattering. It is found that the smallest domain size of P3HT is introduced by replicating the fluorine-doped tin oxide structure underneath. The structure sizes of the P3HT:PCBM active layer are further optimized after thermal annealing. Compared to devices with standard geometry, the P3HT:PCBM layer in the inverted solar cells shows smaller domain sizes, which are much closer to the exciton diffusion length in the polymer. The decrease in domain sizes is identified as the main reason for the improvement of the device performance.